SAB 87
Schemes
Spare parts for compressor SAB 87
0662-831 rev. 00.06 | |||
List of parts for SAB 87 | |||
Relevant drawing document: 0662-830 | |||
Pos.nr | Designation | No. | Part no. |
2 | Rotor housing, unclassified | 1 | 3011-030 |
4 | Bearing housing unclassified | 1 | 3013-240 |
5 | Dowel pin | 2 | 2122-027 |
7 | Pair of rotors, unclassified | 1 | 3024-129 |
8 | Gasket | 1 | 2353-191 |
10 | Distance washer | 1 | 3049-050 |
11 | Radial bearing 2320 | 1 | 1513-053 |
12 | Radial bearing 2319 | 1 | 1513-054 |
13 | Radial bearing 2316 | 2 | 1513-055 |
14 | Thrust bearing 7318 | 3 | 1513-056 |
15 | Thrust bearing 7317 | 2 | 1513-057 |
16 | Nut M85x2 | 1 | 1514-021 |
18 | Shaft seal | 1 | 1332-033 |
19 | Snap Ring | 1 | 3026-045 |
20 | Spacer sleeve | 1 | 3049-048 |
21 | Spacer sleeve | 1 | 3049-049 |
23 | Bearing cover | 1 | 1906420-1 |
24 | Gasket | 1 | 2353-192 |
25 | Seat holder | 1 | 3026-042 |
26 | Oil collector | 1 | 3026-043 |
27 | Gasket | 1 | 2353-193 |
29 | Pipe | 1 | 3026-044 |
32 | Adjusting screw | 3 | 3049-051 |
33 | Protecting washer | 1 | 3049-052 |
34 | Shims | 1 | 2212-139 |
36 | Balancing piston | 1 | 3025-044 |
38 | Cover | 1 | 3013-242 |
39 | Slide valve | 1 | 3049-057 |
40 | Slide valve | 1 | 3049-082 |
41 | Guide block | 1 | 3049-053 |
42 | Cover-Slide valve | 1 | 3013-243 |
43 | Holder | 1 | 3049-054 |
44 | Magnet | 2 | 3043-196 |
45 | Cover-Bearing housing | 1 | 3013-224 |
46 | Dowel pin | 2 | 3049-055 |
47 | Cylinder | 1 | 3043-185 |
48 | Cylinder head | 1 | 3013-245 |
49 | Hydraulic piston | 1 | 3043-186 |
1) only for high pressure compressor | |||
2) only for booster compressor | |||
3) compressor with economiser | |||
4) compressor without economiser |
Pos.nr | Designation | No. | Part no. | |
50 | Piston rod | 1 | 3043-188 | |
51 | Probe | 1 | 3045-068 | |
52 | Spring housing | 1 | 1906447-A | |
53 | Gland | 1 | 3043-192 | |
54 | Washer | 1 | 3043-193 | |
55 | Unloading spring | 1 | 3043-194 | |
56 | Support ring | 1 | 2353-199 | |
57 | Vi-piston | 1 | 3044-075 | 6) |
58 | Vi-cylinder | 1 | 3044-076 | 5) |
59 | Cover, Vi-cylinder | 1 | 3013-249 | 5) |
60 | Gasket | 1 | 2353-194 | |
61 | Hydraulic piston | 1 | 3044-077 | 5) |
62 | Piston rod | 1 | 3044-078 | 5) |
63 | Indicator | 1 | 3044-079 | 5) |
64 | Dowel pin | 1 | 3044-080 | 5) |
66 | Support ring | 1 | 2353-200 | 5) |
67 | Pilot valve | 1 | 1372-208 | 5) |
68 | Cover | 1 | 3013-250 | 5) |
69 | Gasket | 1 | 2353-195 | |
70 | Control piston | 1 | 3044-081 | 5) |
71 | Spring | 1 | 3044-083 | 5) |
72 | Blind cover | 1 | 3013-257 | 7) |
75 | Suction filter | 1 | 3042-115 | |
76 | Gasket | 2 | 2353-196 | |
77 | Filter holder | 1 | 3042-116 | |
78 | Suction filter cover | 1 | 3013-251 | |
79 | Guide | 1 | 3042-117 | |
81 | Blind cover | 1 | 3013-258 | 7) |
82 | Distance ring | 1 | 2124-096 | 8) |
84 | Cover | 1 | 3013-252 | |
85 | Cover | 1 | 3013-253 | |
86 | Cover | 1 | 3013-254 | |
87 | Cover | 1 | 3013-255 | |
88 | Gasket | 1 | 2353-197 | |
89 | Orifice plug Ø8.0 | 2 | 3044-082 | |
95 | Oil pump | 1 | 1524-221 | |
96 | Gasket | 1 | 2353-198 | |
97 | Oil pump holder | 1 | 3041-013 | |
99 | Reducing piston | 1 | 3041-014 | |
109 | Stop valve | 2 | 1374-011 | |
110 | Stop valve | 2 | 1374-012 |
5) Only for compressors with variable Vi | ||||
6) Only for compressors with variable Vi or fixed Vi =4.8 | ||||
7) Only for compressors with fixed Vi =2.6 or 4.8 | ||||
8) Only for compressors with fixed Vi =4.8 |
Pos.nr | Designation | No. | Part no. | |
112 | Compressor sign | 1 | 2516-301 | |
114 | Warning sign | 1 | 2516-302 | |
115 | Stal sign | 1 | 2516-303 | |
116 | Drive screw | 8 | 1414-200 | |
120 | Blind flange DN 25 | 1 | 1344-302 | |
123 | Blind flange DN 65 | 2 | 1344-303 | |
124 | Gasket 43/57x2 | 1 | 2356-065 | |
127 | Gasket 95/109x2 | 2 | 2356-222 | |
128 | Spiral pin 3x10 | 2 | 1446-037 | |
130 | Spiral pin 6x16 | 2 | 1446-038 | |
131 | Parallel pin CPK 10x35 | 2 | 1445-082 | |
132 | Parallel pin 10x30 | 9(7) | 1445-081 | 9) |
134 | Parallel pin 10x120 | 1 | 1445-085 | 5) |
135 | Parallel pin 10x140 | 1 | 1445-086 | 5) |
138 | Tension pin 6x32 | 1 | 1446-039 | |
139 | Grooved pin 4x14 | 1 | 1446-041 | |
141 | Retaining ring SgH 40 | 1 | 1437-150 | 5) |
142 | Retaining ring SgH 70 | 1 | 1437-159 | |
143 | Retaining ring SgH 110 | 1 | 1437-169 | |
145 | Retaining ring SgA 80 | 1 | 1437-230 | 1) |
146 | Retaining ring SgA 100 | 1 | 1437-244 | |
148 | Disc spring | 4 | 3921 9512357 | 8) |
149 | Disc spring | 2 | 1523-039 | |
150 | Disc spring | 8 | 1523-048 | |
151 | Disc spring | 1 | 1523-052 | |
152 | Pressure spring | 1 | 1523-053 | |
153 | Pressure spring | 2 | 1523-037 | |
155 | Plug 1/16" | 9(2) | 1343-021 | 9) |
156 | Plug 1/8" | 11(10) | 1343-022 | 9) |
158 | Plug 3/8" | 16 | 1343-023 | |
160 | Plug G1/4" | 2 | 1343-025 | |
161 | Plug G1/2" | 6 | 1343-027 | |
162 | Plug G3/4" | 9 | 1343-028 | |
163 | Plug G1" | 3 | 1343-030 | |
165 | Gasket 14/21 | 2 | 2356-320 | |
166 | Gasket 21/28 | 6 | 2356-321 | |
167 | Gasket 27/33 | 10 | 2356-322 | |
168 | Gasket 34/42 | 3 | 2356-323 | |
169 | Gasket 34/43x2,5 | 1 | 2356-324 |
2) Only for booster compressor | |
5) Only for compressors with variable Vi | |
8) Only for compressors with fixed Vi =4.8 | |
9) No. in ( ) for compressors with fixed Vi |
Pos.nr | Designation | No. | Part no. | |
170 | Slide ring | 1 | 1243-020 | 5) |
171 | Slide ring | 1 | 1243-020 | |
173 | Sealing ring | 1 | 1332-034 | |
174 | Sealing ring | 1 | 1332-037 | 5) |
175 | Sealing ring | 1 | 1332-039 | |
176 | Sealing ring | 1 | 1332-041 | 5) |
177 | Sealing ring | 1 | 1332-042 | |
180 | Sight glass | 1 | 1226-029 | |
181 | Check valve | 1 | 1364-200 | |
182 | Check valve | 1 | 1364-197 | |
184 | V-ring | 1 | 1332-036 | |
187 | O-ring 10,3x2,4 | 1 | 1331-343 | |
188 | O-ring 15,3x2,4 | 3 | 1331-344 | |
191 | O-ring 19,2x3 | 1 | 1331-345 | |
192 | O-ring 24,2x3 | 1 | 1331-346 | 5) |
193 | O-ring 29,2x3 | 1 | 1331-347 | 5) |
194 | O-ring 39,2x3 | 1 | 1331-348 | 5) |
195 | O-ring 44,2x3 | 2 | 1331-349 | |
196 | O-ring 49,5x3 | 2 | 1331-350 | |
197 | O-ring 54,5x3 | 1 | 1331-351 | |
199 | O-ring 69,5x3 | 1 | 1331-352 | |
200 | O-ring 79,5x3 | 1 | 1331-353 | |
203 | O-ring 109,5x3 | 2 | 1331-354 | |
204 | O-ring 114,5x3 | 1 | 1331-355 | |
205 | O-ring 124,5x3 | 1 | 1331-357 | |
206 | O-ring 129,5x3 | 1 | 1331-358 | |
207 | O-ring 49,2x5,7 | 2(1) | 1331-359 | 9) |
208 | O-ring 149,3x5,7 | 1 | 1331-360 | |
209 | O-ring 159,3x5,7 | 2 | 1331-361 | |
210 | O-ring 184,3x5,7 | 2 | 1331-362 | |
211 | O-ring 279,3x5,7 | 1 | 1331-363 | |
214 | Hexagon screw M 12x35 | 4 | 3921 2120538 | |
216 | Hexagon screw M 16x45 | 32 | 1413-433 | |
223 | Grub screw 6x16 | 2 | 1413-231 | |
228 | Hex. socket screw 5x30 | 4 | 1413-035 | |
230 | Hex. socket screw 6x16 | 6 | 1413-340 | |
231 | Hex.socket screw 10x25 | 4 | 1413-371 | |
232 | Hex. socket screw 10x25 | 15 | 1413-371 | |
233 | Hex.socket screw 10x30 | 9(7) | 1413-372 | 9) |
5) Only for compressors with variable Vi | |
9) No. in ( ) for compressors with fixed Vi |
Pos.nr | Designation | No. | Part no. | |
234 | Hex. socket screw 10x35 | 23 | 1413-373 | |
235 | Hex. socket screw 10x40 | 10 | 1413-374 | |
236 | Hex. socket screw 10x45 | 2 | 1413-375 | |
238 | Hex. socket screw 10x90 | 5 | 1413-380 | |
239 | Hex. socket screw 10x110 | 3 | 1413-393 | 5) |
241 | Hex. socket screw 12x30 | 17 | 1413-386 | |
242 | Hex. socket screw 12x35 | 4 | 1413-387 | |
243 | Hex. socket screw 12x50 | 8 | 1413-390 | |
244 | Hex. socket screw 12x65 | 24 | 1413-401 | |
249 | Hex. socket screw 16x55 | 32 | 1413-036 | |
256 | Nipple | 2 | 1343-023 | |
258 | Nipple | 1 | 1349-230 | |
270 | Protecting cover | 1 | 1246-059 | |
275 | Solenoid valve | 1 | 1372-216 | |
276 | Orifice plug 02.0 | 1 | 1371-038 | |
277 | Orifice plug 02.5 | 1 | 1371-039 | |
280 | Position transmitter | 1 | 1553-220 |
5) Only for compressors with variable Vi |
9) No. In ( ) for compressors with fixed Vi |
Large tool set for SAB 87 compressors |
The tools specified below are needed for major overhauls and repairs (e.g. service after 40 000 operating |
hours or changing bearings). These tools named the large tool set must be supplemented with the so- |
called small tool set article no. 3083.189. See Document no. 0662-804 |
List of tools in the tool set 1906 147-A |
Item | Designation | quantity | Article no. |
1 | Tool box | 1 | 1906 147-1 |
2 | Sleeve for bearing nut .screw | 1 | 1906380-A |
3 | Sleeve for bearing nut, slide | 1 | 1906481-A |
4 | Yoke | 1 | 1906490-1 |
5 | Level arm | 1 | 1906491-1 |
6 | Holder | 2 | 1906454-A |
7 | Holder | 1 | 1906455-A |
8 | Holder | 1 | 1906456-A |
9 | Tie rod | 2 | 1906 136-1 |
10 | Tie rod | 1 | 1906 137-1 |
12 | Dismounting tool for radial bearing | 1 | 1906075-1 |
13 | Dismounting tool for radial bearing | 1 | 1906094-1 |
14 | Dismounting tool for radial bearing | 1 | 1906095-1 |
15 | Sleeve | 1 | 1906098-1 |
16 | Assembling tool for bearing | 1 | 1906484-1 |
17 | Washer | 1 | 1906485-1 |
18 | Adapter | 1 | 1906486-1 |
20 | Guide | 1 | 1906488-1 |
21 | Guide | 1 | 1906489-1 |
22 | Level arm | 1 | 1906 138-1 |
23 | Guide | 1 | 1906478-1 |
24 | Guide | 1 | 1906478-2 |
25 | Guide | 1 | 1906478-3 |
26 | Guide | 1 | 1906492-1 |
32 | Feeler gauge | 1 | 1878747-A |
33 | Retaining-ring pliers | 1 | 1906 147-33 |
34 | Socket head sleeve | 1 | 1906 147-34 |
35 | Socket head sleeve | 1 | 1906 147-35 |
36 | Socket head sleeve | 1 | 1906 147-36 |
37 | Socket head sleeve | 1 | 1906 147-37 |
38 | Adapter | 1 | 1906 147-38 |
40 | Hexagon socket screw key | 1 | 1906 147-40 |
41 | Ratched-ring key | 1 | 1906 147-41 |
42 | Flange nut | 2 | 1906 144-42 |
43 | Flange nut | 1 | 1906 147-43 |
45 | Thrust bearing | 1 | 1906 147-45 |
47 | Lifting eye | 1 | 39 218 333 534 |
48 | Lifting eye | 1 | 39 218 333 670 |
50 | Screw | 4 | 39212120532 |
51 | Hexagon screw | 1 | 1906 147-51 |
52 | Hexagon screw | 1 | 1906 147-52 |
55 | Grub screw | 1 | 1906 147-55 |
60 | Guide | 2 | 1905777-1 |
Small tool set for SAB 81- 83 - 85 - 87 - 89 compressors |
This tool set contains the tools needed to align the electric motor, to replace a shaft seal, to replace a |
visual indicator seal and to replace a coupling. Each compressor should be provided with this tool set. |
For major overhaul work (replacing bearings e.g.), this tool set must be supplemented with the large tool |
set - see doc.no. 0662-803 (SAB 81), 0662-813 (SAB 83) , 0662-823 (SAB 85) , 0662-833 (SAB 87) or |
0662-843 (SAB 89). |
List of tools in the tool set 3083.189 |
Item | Designation | quantity | Article no. |
1 | Tool box | 1 | 1906139-1 |
2 | Alignment device for coupling | 1 | 3183.105 |
3 | Feeler gauge (incl. In 3183.105) | 2 | 1622.050 |
4 | Level arm | 1 | 1906 152-1 |
5 | Puller screw | 2 | 1906 153-1 |
6 | Guiding pin | 2 | 1906 154-1 |
7 | Dismantling tool | 1 | 1906 155-1 |
8 | Puller screw | 2 | 1905 156-1 |
9 | Guide | 1 | 1906 157-A |
15 | Screw M 14x40 | 2 | 1906 140-15 |
16 | NutM12 | 2 | 1906 140-16 |
17 | NutM6 | 2 | 1906 140-17 |
18 | Hexagon key 4 mm | 1 | 1906 140-18 |
19 | Hexagon key 5 mm | 1 | 1906 140-19 |
20 | Hexagon key 12 mm | 1 | 1906 140-20 |
21 | Socket-head sleeve 6 mm | 2 | 1906 140-21 |
22 | Socket-head sleeve 8 mm | 1 | 1906 140-22 |
23 | Socket-head sleeve 10 mm | 1 | 1906 140-23 |
Spare Parts for service on SAB 87 compressor | |||
The spare parts listed below are needed for the following service jobs. For separate gaskets or | |||
items -see part list for compressor Document no.0662-831 | |||
The relevant drawing document: 0662-830 |
Cleaning of suction filter Part no. 3084-719 | No. | Designation | Pos. no. | Remarks | |
2 | Gasket | 76 | |||
2 | Gasket | 127 | D= 109/95x2 | ||
1 | O-ring | 211 | 279,3x5,7 | ||
Change of seal for visual position indicator Part no. 3084-706 | No. | Designation | Pos. no. | Remarks | |
1 | Sealing ring | 173 | |||
1 | Sealing ring | 56 | |||
1 | O-ring | 191 | 19,2x3 | ||
1 | O-ring | 195 | 44,3x3 | ||
1 | O-ring | 206 | 129,5x3 | ||
Change of seal for indication ofVi-piston Part no. 3084-707 | No. | Designation | Pos.no. | Remarks | |
1 | Sealing ring | 174 | |||
1 | Support ring | 66 | |||
1 | O-ring | 193 | 29,2x3 | ||
1 | O-ring | 205 | 124.5x3 | ||
Inspection of rotors Part no. 3084-720 | No. | Designation | Pos. no. | Remarks | |
1 | Gasket | 60 | |||
2 | Gasket | 76 | |||
1 | Gasket | 88 | |||
2 | Gasket | 127 | D= 109/95x2 | ||
1 | O-ring | 211 | 279.3x5,7 | ||
Change of oil pump Part no. 3084-717 | No. | Designation | Pos. no. | Remarks | |
1 | Oil pump | 95 | |||
1 | Gasket | 96 | |||
2 | Tension pin | 130 | 6x16 | ||
Change of shaft seal Part no. 3084-716 | No. | Designation | Pos.no. | Remarks | |
1 | Shaft seal | 18 | |||
1 | O-ring | 203 | 109.5x3 | ||
1 | O-ring | 204 | 114.3x3 | ||
1 | V-ring | 184 | |||
1 | Gasket | 27 | |||
1 | Gasket | 167 | |||
Capacity control | 1 | Complete solenoid valve but without orifices | 1921 438-1 | 240 V/60 Hz | |
220 V/50 Hz | |||||
1 | 1921 438-2 | 120 V/60 Hz | |||
110 V/50 Hz | |||||
1 | 1921 438-3 | 24 V/50-60 Hz | |||
2 | Coil | 1921 470-1 | 240 V/60 Hz | ||
220 V/50 Hz | |||||
2 | 1921 470-2 | 120 V/60 Hz | |||
110 V/50 Hz | |||||
2 | 1921 470-3 | 24 V/50-60 Hz | |||
1 | Orifice conn. P | 277 | Ø2,3mm | ||
1 | Orifice conn. T | 276 | Ø2,0mm | ||
4 | O-ring | 9,25x1,78 | |||
Change of bearing or complete overhaul Part no. 3084-548 | No. | Designation | Pos.no. | Remarks | |
1 | Set of gaskets | 3084-701 | |||
1 | Radial bearing | 11 | |||
1 | Radial bearing | 12 | |||
2 | Radial bearing | 13 | |||
3 | Thrust bearing | 14 | |||
2 | Thrust bearing | 15 | |||
1 | Shaft seal kit | 18 | 3084-716 | ||
1 | Shim | 34 | 0.1 |