CMO 24-26-28 and TCMO 28 Mk2
Description for compressors
SMC 104-106-108 и TSMC 108 Mk3, S-L-E
The SMC 100 and TSMC 100 compressors have 100 mm diameter pistons, as indicated by the first digit in the type designation. The number of cylinders in the compressor block is indicated by the following two digits, where, for example, SMC 108 is an 8-cylinder compressor. SMC 100 is a one-stage compressor which compresses the gas in a single stage.
In the TSMC 100 two-stage compressors, the gas is compressed in two stages at a ratio of 1:3 between the number of high- and lowpressure cylinders. Thus, a TSMC 108 has 2 high-pressure cylinders and 6 low-pressure cylinders. The SMC 100 and TSMC 100 are available in three versions: an S-type with 80 mm stroke, an L-type with 100 mm stroke, and an E-type with 120 mm stroke.
Тип компрессора можно определить по заводской табличке, расположенной на торцевой стороне компрессора, обращенной в противоположную сторону от муфты или ременного привода. На рисунке ниже показана заводская табличка САБРО.
| 25% | 33% | 50% | 67% | 75% | 100% | |
| СМ0 24 | X | X | ||||
| СМ0 26 | X | X | X | |||
| СМ0 28 | X | X | X | X | ||
| ТСМО 28 | X | X | X |
Compressor data for reciprocating compressors SMC 104-106-108 и TSMC 108 Mk3, S-L-E
Operating limits
SABROE prescribes operating limits within which the compressor and any additional equipment must operate. These limits for R717, R22, R134a, R404A, R507 and R407C are shown in the following tables, together with the main data for the compressor.
| Compressor type |
Number of cylinders |
Bore mm |
Stroke mm |
Max/min Speed RPM |
Swept volume max RPM* m3/h |
Weight (max.) compr. block kg |
| SMC 104S SMC 106S SMC 108S | 4 6 8 |
100 100 100 |
80 80 80 |
1500/700 1500/700 1500/700 | 226 339 452 |
580 675 740 |
| TSMC 108S | 2+6 ** | 100 | 80 | 1500/700 | 339 | 775 |
| SMC 104L SMC 106L SMC 108L |
4 6 8 |
100 100 100 |
100 100 100 |
1500/700 1500/700 1500/700 | 283 424 565 |
580 675 740 |
| TSMC 108L | 2+6* | 100 | 100 | 1500/700 | 424 | 775 |
| SMC 104E SMC 106E SMC 108E | 4 6 8 |
100 100 100 |
120 120 120 |
1500/700 1500/700 1500/700 | 339 509 679 |
600 700 770 |
| TSMC 108E | 2+6* | 100 | 120 | 1500/700 | 509 | 800 |
* The max speed permitted can be lower than stated here depending on operating conditions and refrigerant; please see the following diagrams.
** Two - stage compressors (High Stage cylinders and Low Stage cylinders).
Schemes
Spare parts for SMC 104-106-108 & TSMC 108 Mk3 Type S-L и E
| Spare parts for SMC 104-106-108 & TSMC 108 Mk3 Type S-L and E | |||||||
| Relevant drawings for compressor | SMC | TSMC | |||||
| SMC 100 Mk 3, S-L-E (delivered after 89 - 10) | 0661-521 | 0661-522 | |||||
| Cylinder liner ect. SMC - TSMC 104,106, 108 Mk 3 (after 89.10) | 0661-520 | ||||||
| SMC 100 M k3 | 0661-755 | 0661-756 | |||||
| Cylinder liner ect. SMC - TSMC 100 Mk3 | 0661-605 | ||||||
| *) If the compressor runs as heat pump, this must be mentioned when ordering, to ensure a correct delivery | |||||||
| Pos. | Designation | Weight each in kg | Number each compresssor | Part No | |||
| SMC 104 | SMC 106 | SMC 108 | TSMC 108 | ||||
| Compressor frame | |||||||
| 1A-1 | Frame SMC 104 | 240.000 | 1 | 3111-065 | |||
| 1A-2 | Frame SMC 106 | 274.000 | 1 | 3111-066 | |||
| 1A-3 | Frame SMC 108 | 285.000 | 1 | 3111-067 | |||
| 1 A-4 | Frame TSMC 108 | 290.000 | 1 | 3111-068 | |||
| 1B-1 | Oil levei glass dia. 80 | 0.230 | 1 | 1 | 1 | 1 | 1226-015 |
| 1C-1 | O-ring PRP 137 - 52,07 x 2,62 *) | 0.002 | 1 | 1 | 1 | 1 | 1331-140 |
| 1D-1 | Hexagon head MS x 16 | 0.010 | 4 | 4 | 4 | 4 | 1424-148 |
| Top cover - air cooled | |||||||
| 2A-1 | Top cover S-L, | 19.000 | 1 | 2 | 3 | 2 | 3113-191 |
| 2A-2 | Top co^er with fiange S-L | 20.500 | 1 | 1 | 1 | 2 | 3113-192 |
| 2A-3 | Top cover E | 19.000 | 1 | 2 | 3 | 2 | 3113-177 |
| 2A-4 | Top cover with flange E | 20.500 | 1 | 1 | 1 | 2 | 3113-176 |
| 2C-1 | Gasket for top cover | 0.020 | 2 | 3 | 4 | 4 | 2353-151 |
| 2D-1 | Hexagon head M14x90 | 0.120 | 30 | 46 | 62 | 60 | 1424-083 |
| 2F-1 | Hexagon head M14 x 120 | 0.165 | 2 | 2 | 2 | 4 | 1424-090 |
| 2G-1 | Washer for M14 dia- 28/15 x 2,5 | 0.010 | 32 | 48 | 64 | 64 | 1436-037 |
| Top cover-water cooled (see sketch below) | |||||||
| 2A-1 | Top cover S-L | 19.000 | 1 | 2 | 3 | 2 | 3113-191 |
| 2A-2 | Top cover with flange S-L | 20.500 | 1 | 1 | 1 | 2 | 3113-192 |
| 2A-3 | Top cover E | 19.000 | 1 | 2 | 3 | 2 | 3113-177 |
| 2A-4 | Top cover with flange E | 20.500 | 1 | 1 | 1 | 2 | 3113-176 |
| 2B-1 | Water cover for cover with flange | 5.800 | 1 | 1 | 1 | 2 | 3113-195 |
| 2B-2 | Water cover left | 5.800 | 1 | 1 | 2 | 2 | 3113-193 |
| 2B-3 | Water cover right | 5.800 | 1 | 1 | 3113-194 | ||
| 2C-1 | Gasket for top cover | 0.020 | 2 | 3 | 4 | 4 | 2353-151 |
| 2D-1 | Gasket for water cover pos. 2B-1 | 0.020 | 1 | 1 | 1 | 2 | 2353-176 |
| 2D-2 | Gasket for water cover pos, 2B-2/2B-3 | 0.020 | 1 | 2 | 3 | 2 | 2353-175 |
| 2E-2 | Hexagon head screw M14 x 110 | 0.150 | 30 | 46 | 62 | 60 | 1424-087 |
| 2F-1 | Hexagon head screw M14 x 120 | 0.165 | 2 | 2 | 2 | 4 | 1424-090 |
| 2G-1 | Washer for Mt4, dia, 28/15 x 2,5 | 0.010 | 32 | 48 | 64 | 64 | 1436-037 |
| 2H-1 | Hexagon head screw Mi 0 x 35 | 0.050 | 4 | 5 | 8 | 9 | 1424-193 |
| 2J-1 | Washer for M10, dia. 21/10,5 x 2 | 0.008 | 4 | 6 | 8 | 8 | 1436-035 |
| Side cover o sir cooled | |||||||
| 3A-1 | Side cover | 10.900 | 2 | 2 | 2 | 2 | 3113-148 |
| 3C-1 | Gasket for side cover | 0.020 | 2 | 2 | 2 | 2 | 2353-151 |
| 3E-1 | Hexagon head screw M14 x 65 | 0,045 | 32 | 32 | 32 | 32 | 1424-246 |
| 3G-1 | Washer for M14, dia. 28/15 x 2.5 | 0.010 | 32 | 32 | 32 | 32 | 1436-037 |
| Side cover - water cooled | |||||||
| 3A-2 | Side cover t 15,000 | 15.000 | 2 | 2 | 2 | 2 | 3113-140 |
| 3B-1 | Water cover | 5.800 | 2 | 2 | 2 | 2 | 3113-138 |
| 3C-1 | Gasket for side cover | 0.020 | 2 | 2 | 2 | 2 | 2353-151 |
| 3D-1 | Gasket for water cover | 0.020 | 2 | 2 | 2 | 2 | 2353-154 |
| 3E-2 | Hexagon head screw M14 x 55 | 0.065 | 28 | 28 | 28 | 28 | 1424-244 |
| 3F-1 | Hexagon head screw M14 x 35 | 0.045 | 4 | 4 | 4 | 4 | 1424-240 |
| 3G-1 | Washer for M14, dia. 28/15 x 2,5 | 0.010 | 32 | 32 | 32 | 32 | 1436-037 |
| 3H-1 | Hexagon head screw M 12 x 40 | 0.050 | 2 | 2 | 2 | 2 | 1424-217 |
| 3J-1 | Washer for M12. dia. 24/13 x 2,5 | 0.008 | 2 | 2 | 2 | 2 | 1436-036 |
| End cover at pump end | |||||||
| 4A-1 | End cover | 17.950 | 1 | 1 | 1 | 1 | 3113-028 |
| 4B-1 | Gasket | 0.020 | 1 | 1 | 1 | 1 | 2353-011 |
| 4C-1 | Hexagon head screw M14 x 100 | 0.150 | 14 | 14 | 14 | 14 | 1424-085 |
| 40-1 | Washer for M14 dia. 28/15x2,5 | 0.010 | 14 | 14 | 14 | 14 | 1436-037 |
| Bearing cover at pump end | |||||||
| 5A-1 | Bearing cover | 9.100 | 1 | 1 | 1 | 1 | 3113-031 |
| 58-1 | Hexagon head screw M14 x 35 | 0,055 | 6 | 6 | 6 | 6 | 1424-240 |
| 5C-1 | Bushing | 1.200 | 1 | 1 | 1 | 1 | 2132-021 |
| 5C-2 | Bushing for repair (0,5 mm underside) | 1.220 | 1 | 1 | 1 | 1 | 2132-022 |
| 5D-1 | Gascet-0,3 mm | 0,005 | 1 | 1 | 1 | 1 | 2353-013 |
| 5D-2 | Gascet-0,5 mm | 0,006 | 1 | 1 | 1 | 1 | 2353-100 |
| 5D-3 | Gasket - 0,75 mm | 0.010 | 1 | 1 | 1 | 1 | 2353-014 |
| 5D-4 | Gasket -1.0 mm | 0.015 | 1 | 1 | 1 | 1 | 2353-015 |
| Bearing cover at shaft seal end | |||||||
| 6A-1 | Bearing cover | 23.000 | 1 | 1 | 1 | 1 | 3113-124 |
| 6B-1 | Hexagon head screw M14 x 60 | 0,085 | 14 | 14 | 14 | 14 | 1424-245 |
| 6C-3 | Bushing | 1.200 | 1 | 1 | 1 | 1 | 2132-021 |
| 6C-4 | Bushing for repair (0,5 mm undersize) | 1.200 | 1 | 1 | 1 | 1 | 2132-022 |
| 6D-1 | Gasket | 0.020 | 1 | 1 | 1 | 1 | 2353-011 |
| 6E-1 | Washer for M14, dia. 28/15 x 2,5 | 0.010 | 14 | 14 | 14 | 14 | 1436-037 |
| 6F | Valve for prelubrication | 1 | 1 | 1 | 1 | 2412-585 | |
| 6G | Nut | 1 | 1 | 1 | 1 | 2313-045 | |
| 6H | Speciai joint | 1 | 1 | 1 | 1 | 2334-027 | |
| 6J | Cap | 1 | 1 | 1 | 1 | 2313-027 | |
| 6K | Joint 3/8" | 1 | 1 | 1 | 1 | 1349-053 | |
| 6L | Alu gasket | 1 | 1 | 1 | 1 | 2356-123 | |
| Shaft seal cover for type SB100 | |||||||
| 8A-2 | Shaft seal cover Δ | 1 | 1 | 1 | 1 | 3113-215 | |
| 8B-1 | Gasket for shaft seal Δ | 1 | 1 | 1 | 1 | 2353-005 | |
| 8C-1 | Hexagon head screw M10 x 40 Δ | 6 | 6 | 6 | 6 | 1424-194 | |
| 8D-1 | Hose connection G 1/4" Δ | 1 | 1 | 1 | 1 | 1345-143 | |
| 8E-1 | Plastic hose 3/16" x 300 Δ | 1 | 1 | 1 | 1 | 1241-190 | |
| 8F-1 | Splash ring Δ | 1 | 1 | 1 | 1 | 1437-295 | |
| 8G-1 | Locking ring dia. 111/105 x 3 | 1 | 1 | 1 | 1 | 3126-169 | |
| 8H-1 | Groover pin dia. 4x20 | 1 | 1 | 1 | 1 | 1446-081 | |
| Shaft seat type SB 100 | |||||||
| 10-3 | Shaft seal complete,includes all parts | 1 | 1 | 1 | 1 | 3126-177 | |
| marked Δ | |||||||
| for compressor nos,after 98379 incl. | |||||||
| 10-4 | Shaft seal to replace incl.part nos | 1 | 1 | 1 | 1 | 3126-170 | |
| 10E-2, 10F-1. 10D-1, 10G-1. 10J-1, | |||||||
| 10L-2 | |||||||
| for compressor nos.up to 98378 incl. | |||||||
| 10-5 | Shaft seal to replace incl.part nos | 1 | 1 | 1 | 1 | 3126-178 | |
| 10E-2. 10F-1, 10D-1, 10G-2, 10L-2, | |||||||
| 10J-1 | 1 | ||||||
| for compressor nos.up to 98379 incl. | |||||||
| 10A-1 | Retaining flange Δ | 1 | 1 | 1 | 1 | 3126-166 | |
| 10B-1 | Spring Δ | 10 | 10 | 10 | 10 | 2142-058 | |
| 10D-1 | O-ring dia. 75,6 X 3,5 *) Δ | 1 | 1 | 1 | 1331-075 | ||
| 10E-2 | Slide ring(cast iron) Δ | 1 | 1 | I | 1 | 3126-175 | |
| 10F-1 | Slide ring (special carbon) Δ | 1 | 1 | I | 1 | 3126-168 | |
| 10G-1 | O-ring dia. 82.15 X 3.5 *) | 1 | 1 | 1 | 1 | 1331-077 | |
| 10G-2 | Seating ring Δ | 1 | 1 | 1 | 1 | 1332-124 | |
| 10H-1 | Locking ring Δ | 1 | 1 | 1 | 1 | 3126-153 | |
| 10J-1 | Socket cap screw M 5x 16 Δ | 4 | 4 | 4 | 4 | 1413-329 | |
| 10L-2 | Back-up ring Δ | 1 | 1 | 1 | 1 | 1332-125 | |
| 10M-2 | Locking ring Δ | 1 | 1 | 1 | 1 | 1437-046 | |
| Oil pump | |||||||
| 11-1 | Oil pump | 2.400 | 1 | 1 | 1 | 1 | 3141-004 |
| 11A-1 | Housing | 0.800 | 1 | 1 | 1 | 1 | |
| 11B-1 | Cover | 0.800 | 1 | 1 | 1 | 1 | |
| 11E -1 | Gear wheel | 0.330 | 1 | 1 | 1 | 1 | |
| 11F-1 | Gear wheel | 0.400 | 1 | 1 | 1 | 1 | |
| 11G-1 | Gear wheli for pump pinion | 0.660 | 1 | 1 | 1 | 1 | 3141-046 |
| 11H-1 | Gear wheel | 0.530 | 1 | 1 | 1 | 1 | 3141-047 |
| 11J-1 | Lock nut M10 x 10,7 | 0.015 | 1 | 1 | 1 | 1 | 1433-080 |
| 11K-1 | Gasket - paper - 0.2 mm | 0.001 | 1 | 1 | 1 | 1 | 2353-021 |
| 11L-1 | Washer for M 10dia. 21/10,5 x 2 | 0.005 | 1 | 1 | 1 | 1 | 1436-035 |
| 11M-1 | Hexagon head screw M 6 x 30 | 0.010 | 4 | 4 | 4 | 4 | 1424-153 |
| 11N -1 | Key - 5 x 5 x 12 | 0.002 | 1 | 1 | 1 | 1 | 1526-050 |
| 11P-1 | Gasket dia. 32/27 x 1,5 | 0.005 | 1 | 1 | 1 | 1 | 2356-139 |
| 11Q-1 | Hexagon head screw M12 x 25 | 0.040 | 2 | 2 | 2 | 2 | 1424-215 |
| 11R-1 | Spring washer dia. 12 | 0.002 | 2 | 2 | 2 | 2 | 1437-081 |
| 11 S-1 | Threaded nipple - 3/4" x 7/8" BSP | 0.230 | 1 | 1 | 1 | 1 | 2311-007 |
| 11T-1 | Spring washer - dia- 11,1 /6.1 x 1,6 | 0.005 | 8 | 8 | 8 | 8 | 1437-022 |
| 11U-1 | Hexagon head screw M 6 x 35 | 0.012 | 4 | 4 | 4 | 4 | 1424-155 |
| 11V -1 | Guide pin | 2 | 2 | 2 | 2 | 1445-066 | |
| Unloading cylinder | |||||||
| 12-1 | Unloading cylinder | 1,765 | 1 | 1 | 1 | 3135-149 | |
| Complete L=75, S=21.5 | |||||||
| 12-2 | Unloading cylinder | 1.790 | 1 | 1 | 1 | 1 | 3135-150 |
| Complete L=100. S=46,5 | |||||||
| 12-3 | Unloading cylinder | 1.815 | 1 | 1 | 1 | 3135-151 | |
| Complete L=125, S=71,5 | |||||||
| 12-4 | Unloading cylinder | 1.840 | 1 | 1 | 3135-152 | ||
| Complete L=150, S=96,5 | |||||||
| 12-5 | Unloading cylinder (HP) | 1,8 | 1 | 3135-161 | |||
| Complete L=82, S=24,5 | |||||||
| 12A-1 | Unloading cylinder | 1.700 | 2 | 3 | 4 | 3 | 3135-147 |
| (SMC and TSMC LP) | |||||||
| 12A-2 | Unloading cylinder | 1.800 | 1 | 3135-148 | |||
| (TSMC HP) | |||||||
| 12B-1 | Piston | 0.220 | 2 | 3 | 4 | 4 | 3135-034 |
| 12C-1 | Piston rod 75 mm (SMC only) | 0.065 | 1 | 1 | 1 | 3135-041 | |
| 12C-2 | Piston rod 100 mm | 0.090 | 1 | 1 | 1 | 1 | 3135-042 |
| 12C-3 | Piston rod 125 mm | 0.115 | 1 | 1 | 1 | 3135-043 | |
| 12C-4 | Piston rod 150 mm | 0.140 | 1 | 1 | 3135-044 | ||
| 12C-5 | Piston rod 82 mm,grounded | 0.090 | 1 | 3135-140 | |||
| (TSMC HP only) | |||||||
| 12D-1 | Threaded plug - 3/8" BSP | 0.065 | 2 | 3 | 4 | 4 | 2314-025 |
| 12E-1 | Gasket dia. 25/17 x 1,5 | 0.002 | 2 | 3 | 4 | 4 | 2356-130 |
| 12F-1 | Seeger ring dia. 52 (SMC and TSMC LP) | 0.008 | 2 | 3 | 4 | 3 | 1437-155 |
| 12G-1 | Spring guide | 0.040 | 2 | 3 | 4 | 4 | 2145-004 |
| 12H-1 | Spring retainer (SMC and TSMC LP) | 0.110 | 2 | 3 | 4 | 3 | 3135-057 |
| 12J-1 | Spring (outer) | 0.065 | 2 | 2 | 4 | 4 | 2142-056 |
| 12J-2 | Spring (inner) | 0.035 | 2 | 3 | 4 | 4 | 2142-055 |
| 12K-1 | Benzing ring - dia. 9 mm | 0,002 | 2 | 3 | 4 | 4 | 1437-105 |
| 12K-2 | Benzing ring - dia. 7 mm (SMC and TSMC LP) | 0.001 | 2 | 3 | 4 | 3 | 1437-103 |
| 12L-1 | Hexagon head screw M10 x 30 | 0.030 | 8 | 12 | 16 | 16 | 1424-192 |
| 12M-1 | Cover (TSMC HP only) | 0.800 | 1 | 3135-105 | |||
| 12N-1 | Gasket for cover (TSMC HP only) | 0.010 | 1 | 2353-025 | |||
| 12P-1 | Look nut - UNF 3/8" (TSMC HP only) | 0.010 | 1 | 1433-100 | |||
| 12Q-1 | Socket cap screw M4 x 16 (TSMC HP only) | 0.010 | 6 | 1413-007 | |||
| 12R-1 | 0-ring PRP n 2 12.37x2,62 (TSMC HP only)") | 0.001 | 1. | 1331-013 | |||
| 12S-1 | Oasket 100 x 100x2 | 0.010 | 2 | 3 | 4 | 4 | 2354-023 |
| Frame for unloading mechanism | |||||||
| Frame compiete incl. pos. 13E-1 | 3184-216 | ||||||
| 13A-1 | Suspension rod | 0.290 | 2 | 3 | 4 | 4 | |
| 13B-1 | Suspension rod | 0.290 | 2 | 3 | 4 | 4 | |
| 13C-1 | Cross piece | 0.330 | 2 | 3 | 4 | 4 | |
| 13D-1 | Cross piece | 0.330 | 2 | 3 | 4 | 4 | 3135-188 |
| 13E-1 | Countersunk screw M6 x 16 | 0,020 | 8 | 12 | 16 | 16 | 1413-092 |
| Bracket for unloading mechanism | |||||||
| 14A-1 | Bracket with pin | 0.065 | 4 | 6 | 8 | 7 | 3135-060 |
| 14B.1 | Spacing ring | 0.005 | 8 | 12 | 16 | 14 | 2124-003 |
| 14C-1 | Hexagon head screw M6 x 30 | 0.010 | 8 | 12 | 16 | 14 | 1424-154 |
| 14D-1 | Spring washer - dia. 6 | 0.005 | 8 | 12 | 16 | 14 | 1437-022 |
| Rocker for unloading mechanism | |||||||
| 15A-1 | Rocker | 0.050 | 8 | 12 | 16 | 16 | 3135-096 |
| 15B-1 | Bearing for SMC and TSMC LP | 0.006 | 8 | 12 | 16 | 12 | 3135-099 |
| 15B-2 | Bearing for TSMC HP | 0.006 | 4 | 3135-101 | |||
| 15C-1 | Spring retainer | 0.001 | 8 | 12 | 16 | 16 | 2145-001 |
| 15D-1 | Spring | 0.007 | 8 | 12 | 16 | 16 | 2142-061 |
| 15E-1 | Washer for bearing cup - 0.5 mm | 0.001 | 2114-003 | ||||
| Crankshaft -all without certificate | |||||||
| 16A-1 | Crankshaft for SMC 104S,complete | 42.400 | 1 | 3121-018 | |||
| 16A -2 | Crankshaft for SMC 106S, complete | 45.400 | 1 | 3121-019 | |||
| 16A -3 | Crankshaft for SMC 108S and TSMC 108S, complete | 47.600 | 1 | 1 | 3121-020 | ||
| 16A -4 | Crankshaft for SMC 104L, complete | 45.600 | 1 | 3121-104 | |||
| 16A -5 | Crankshaft for SMC 106L, compieie | 47.800 | 1 | 3121-105 | |||
| 16A -6 | Crankshaft for SMC 108L and TSMC 108L, complete | 50.600 | 1 | 1 | 3121-106 | ||
| 16A-11 | Crankshaft for SMC 104E, complete | 1 | 3121-213 | ||||
| 16A -12 | Crankshaft for SMC 106E, complete | 1 | 3121-214 | ||||
| 16A -13 | Crankshaft for SMC 108E and TSMC 108E. complete | 3121-215 | |||||
| 16B-1 | Plain washer with pin | 0.800 | 1 | 1 | 1 | 1 | 2125-084 |
| 16C-1 | Key- 18 x 11 x 55 | 0.080 | 1 | 1 | 1 | 1 | 2123-005 |
| 16D-1 | Hexagon head screw M16 x. 55 | 0.050 | 1 | 1 | 1 | 1 | 1424-104 |
| 16E-1 | Spring washer-dia. 16 | 0.004 | 1 | 1 | 1 | 1 | 1437-027 |
| 16F-1 | Plug M12 S-type | 0.010 | 1 | 1 | 1 | 1 | 1413-260 |
| 16F-2 | Plug 1/4" L-type | 0.010 | 3 | 3 | 3 | 3 | 1343-141 |
| Connecting rod | |||||||
| 17-1 | Connecting rod, compieie SMC and TSMC LP | 2.700 | 4 | 6 | 8 | 6 | 3123-004 |
| 17-2 | Connecting rod, complete TSMC HP | 2.700 | 2 | 3123-006 | |||
| 17A-1 | Half-section of bearing | 0.080 | 8 | 12 | 16 | 16 | 2133-003 |
| 17A-2 | Half-section of bearing [0.5 mm undersize) | 0.080 | 8 | 12 | 16 | 16 | 2133-004 |
| 17B-1 | Bushing for piston pin SMC and TSMC LP | 0.200 | 4 | 6 | 8 | 6 | 2132-004 |
| 17B-2 | Needle roller bearing TSMC HP | 0.200 | 2 | 1511-275 | |||
| 17C-1 | Bolt for connecting rod | 0.055 | 8 | 12 | 16 | 16 | 2111-068 |
| 17D-1 | Lock nut-3/8" UNF | 0.010 | 8 | 12 | 16 | 16 | 1433-116 |
| Piston with pin and rings | |||||||
| 18-1 | Piston with pin and rings S | 1.320 | 4 | 6 | 8 | 8 | 3124-002 |
| 18-2 | Piston with pin and rings L | 1.320 | 4 | 6 | 8 | 8 | 3124-052 |
| 18-3 | Piston with pin and rings E | 1.320 | 4 | 6 | 8 | 8 | 3124-065 |
| 18A-1 | Piston pin | 0.500 | 4 | 6 | 8 | 8 | 3125-084 |
| 18B-1 | Piston ring | 0.025 | 8 | 12 | 16 | 16 | 3125-130 |
| 18C-1 | OH scraper rings | 0.030 | 4 | 6 | 8 | 8 | 3125-065 |
| 18D-1 | Seeger-ring - dia- 40 (inside diameter) | 0.005 | 8 | 12 | 16 | 16 | 1437-150 |
| Cylinder Uner with sction valve | |||||||
| 19-1 | Cylinder liner with suction valve R717, SMC -TSMC LP, S and L | 4.100 | 4 | 6 | 8 | 6 | 3112-085 |
| 19-2 | Cylinder liner with suction valve HFC/HCFC, SMC - TSMC LP, S and L | 4.100 | 4 | 6 | 8 | 6 | 3112-086 |
| 19-3 | Cylinder liner with suction valve R717, SMC-TSMC HP, and L | 4.100 | 2 | 3112-087 | |||
| 19-4 | Cylinder liner with suction valve HFC/HCFC, TSMC HP. S and L | 4.100 | 2 | 3112-088 | |||
| 19-5 | Cylinder liner with suction valve R717, SMC -TSMC LP,E | 4.500 | 4 | 6 | 8 | 6 | 3112-081 |
| 19-6 | Cyiinder liner with suction valve R717. SMC-TSMC HP. E | 4.500 | 2 | 3112-097 | |||
| 19A-1 | Cylinder liner S and L | 3.500 | 4 | 6 | 8 | 8 | 3112-065 |
| 19A-2 | Cylinder liner, E | 4.000 | 4 | 6 | 8 | 8 | 3112-080 |
| 19B-1 | Unloading rings with pins, S and L | 0.400 | 4 | 6 | 8 | 8 | 3135-054 |
| 19B-2 | Unloading'rings with pins, E | 0.500 | 4 | 6 | 8 | 8 | 3135-173 |
| 19C-1 | Washer - dia. 8/4,3 x 0,5 | 0.001 | 24 | 36 | 48 | 48 | 2114-001 |
| 19D-1 | Spring for unloading ring | 0.001 | 24 | 36 | 48 | 48 | 2142-034 |
| 19E-1 | Tension spring - 342 mm | 0.015 | 4 | 6 | 8 | 8 | 2142-048 |
| 19F-1 | Ring plate for suction valve | 0.035 | 4 | 6 | 8 | 8 | 3131-021 |
| 19G-1 | Valve spring | 0.001 | 24 | 36 | 48 | 48 | 2141-047 |
| 19H-1 | Suction vaive retaining plate R717 | 1.400 | 4 | 6 | 8 | 8 | 3132-083 |
| 19H-2 | Suction vaive retaining plate R12/R22 | 1.400 | 4 | 6 | 8 | 8 | 3132-095 |
| 19J-1 | Guide ring for discharge valve | 0.450 | 4 | 6 | 8 | 8 | 3134-008 |
| 19K-1 | Gasket for cylinder liner - 0,5 mm | 0.005 | 4 | 6 | 8 | 8 | 2356-111 |
| 19K-2 | Gasket for cylinder liner - 0,8 mm | 0.006 | 4 | 6 | 8 | 8 | 2356-233 |
| 19M-1 | 0-ring 107,55 x 3,53') TSMC HP | 0.002 | 2 | 1331-085 | |||
| 19N-1 | Socket cap screw M6 x 30 | 0.010 | 24 | 36 | 48 | 48 | 1413-343 |
| 19T-1 | Gasket - dia. 163/141 x 0,2 mm | 0.001 | 4 | 6 | 8 | 8 | 2353-140 |
| Discharge valve**) | |||||||
| 20-1 | Discharge valve - R717 - HP | 1.200 | 4 | 6 | 8 | 2 | 3136-089 |
| 20-2 | Discharge valve-R7l7-LP | 1.200 | 4 | 6 | 8 | 6 | 3136-087 |
| 20-3 | Discharge valve - HFC/HCFC - HP | 1.200 | 4 | 6 | 8 | 2 | 3136-088 |
| 20-4 | Discharge valve - HFC/HCFC - LP | 1.200 | 4 | 6 | 8 | 6 | 3136-086 |
| 20-5 | Discharge valve - HFC/HCFC - VHP | 1.200 | 4 | 6 | 8 | 3136-085 | |
| 20A-1 | Discharge valve seat | 0.250 | 4 | 6 | 8 | 8 | 3133-027 |
| 20B-1 | Retaining plate - R717 - HP | 1.000 | 4 | 6 | S | 2 | 3132-092 |
| 20B-2 | Retaining plate - R717-LP | 1.000 | 4 | 6 | 8 | 6 | 3132-085 |
| 20B-3 | Retaining plate - HFC/HCPC - HP | 1.000 | 4 | 6 | 8 | 2 | 3132-093 |
| 20B-4 | Retaining plate - HFC/HCFC - LP | 1.000 | 4 | 6 | 8 | 6 | 3132-091 |
| 20B-5 | Retaining plate - HFC/HCFC - VHP | 1.000 | 4 | 6 | 8 | - | 3132-082 |
| 20C-1 | Ring plate | 0.030 | 4 | 6 | 8 | 8 | 3131-015 |
| 20D-1 | Special screw M 12x 60 | 0.055 | 4 | 6 | 8 | 8 | 1413-121 |
| 20E-1 | Nut M12x 1,25 | 0.015 | 8 | 12 | 16 | 16 | 1432-075 |
| 20F-1 | Spring guide | 0.015 | 4 | 6 | 8 | 8 | 2145-008 |
| 20G-1 | Vaive spring-R717- HP | 0,001 | 32 | 4S | 64 | 16 | 2141-047 |
| 20G-1 | Valve spring-R717-LP | 1.000 | 24 | 36 | 48 | 36 | 2141-047 |
| 20G-1 | Valve spring - HFC/HCFC - HP | 0.001 | 43 | 72 | 56 | 24 | 2141-047 |
| 20G-1 | Valve spring - HFC/HCFC - LP | 0.001 | 24 | 36 | 48 | 36 | 2141-047 |
| 20G-1 | Valve spring - HFC/HCFC - VHP | 0.001 | 64 | 96 | 128 | 2141-047 | |
| Compressors are fitted with disharge valves depending on the working conditions. | ||
| The valve is selected on the bisis of the refrigerant and the condensing/intermediate pressure temperature of | ||
| the plant, indicated in the tabie in 'C. For inst, R22 at TC=53'C=>VHP disharge valve. | ||
| Refri-gerant | Conditions | Valve type |
| R717 | TC< 15°C | LP |
| TC≥15°C | HP | |
| HFC/ HCFC | TC <15°C | LP |
| 45°C R404A-R507 15°C≤ TC<50°C R22 70°C R134a | HP | |
| 15°C≤ TC<50°C R22 | ||
| 70°C R134a | ||
| 45°C R404A-R507 | VHP | |
| TC≥ 50°C R22 | ||
| 70°C134a | ||
| Pos. | Designation | Weight each in kg | Number each compresssor | Part No | |||
| SMC 104 | SMC 106 | SMC 108 | TSMC 108 | ||||
| Spring for safety head | |||||||
| 21A-1 | Spring | 0.400 | 4 | 6 | 8 | 8 | 2142-060 |
| Oil pressure valve | |||||||
| 22A-1 | Oil pressure valve, complete | 0.450 | 1 | 1 | 1 | 1 | 3142-150 |
| 22B-1 | Gasket 90 x 44 x 1 | 0.001 | 1 | 1 | 1 | 1 | 2354-075 |
| 22C-1 | Hexagon head screw M12 x 35 | 0.040 | 2 | 2 | 2 | 2 | 1424-216 |
| Oil charging valve | |||||||
| 23A-1 | Oil charging valve, complete | 0.300 | 1 | 1 | 1 | 1 | 2412-585 |
| 23B-1 | Threaded reducing nipple | 0.155 | 1 | 1 | 1 | 1 | 2311-059 |
| 23C-1 | Socket | 0.075 | 1 | 1 | 1 | 1 | 2313-035 |
| 23D-1 | Gasket | 0.001 | 1 | 1 | 1 | 1 | 2356-123 |
| 23E-1 | Gasket | 0.001 | 1 | 1 | 1 | 1 | 2356-140 |
| 23F-1 | Gasket | 0.001 | 1 | 1 | 1 | 1 | 2356-283 |
| 23G-1 | Nut | 0.060 | 1 | 1 | 1 | 1 | 2313-027 |
| By-pass valves | |||||||
| 24-1 | By-pass valve dia. 20 22 bar TSMC108HP | 2.400 | 1 | 3137-033 | |||
| 24-2 | By-pass vaive dia. 20 24 bar TSMC 108 HP | 2.400 | 1 | 3137-010 | |||
| 24-4 | By-pass valve dia. 28 12 bar TSMC 108LP | 3.600 | 1 | 3137-046 | |||
| 24-5 | By-pass vaive dia. 28 22 bar SMC | 3.600 | 1 | 1 | 1 | 3137-007 | |
| 24-7 | By-pass valve dia, 28 24 bar SMC | 3.600 | 1 | 1 | 1 | 3137-009 | |
| 24B-1 | O-ring for cylinder*) | 0.001 | 1 | 1331-065 | |||
| 24B-4 | O-ring for cylinder*) | 0.002 | 1 | 1 | 1 | 1 | 1331-067 |
| 24C-1 | O-ring for cover*) | 0.002 | 1 | 1331-069 | |||
| 24C-4 | O-ring for cover *) | 0.003 | 1 | 1 | 1 | 1 | 1331-071 |
| 24D-1 | Hexagon head screw M8 x 25 | 0.015 | 4 | 4 | 4 | 8 | 1424-168 |
| 24E-1 | Spring washer dia-14,2/8,2 x2 | 0.002 | 4 | 4 | 4 | 8 | 1437-023 |
| Pos. | Designation | Weight each in kg | Valve dim. | Number each compresssor | Part No | ||||
| SMC 104 | SMC 106 | SMC 108 | TSMC 108 | ||||||
| Stop valves | |||||||||
| 25-1 | Complete valve, disharge KP | 50 | 1 | 2414-073 | |||||
| 25-2 | Complete valve, inlet HP | 50 | 1 | 2411-261 | |||||
| 25-3 | Complete valve, disharge LP | 65 | 1 | 1 | 1 | 1 | 2414-069 | ||
| 25-4 | Complete valve, inlet LP | 100 | 1 | 1 | 1 | 1 | 2414-070 | ||
| 25A-1 | Valve housing | 50 | 1 | 2432-141 | |||||
| 25A-2 | Valve housing | 50 | 1 | 2432-141 | |||||
| 25A-3 | Valve housing | 65 | 1 | 1 | 1 | 1 | 2432-159 | ||
| 25A-4 | Valve housing | 100 | 1 | 1 | 1 | 1 | 2432-160- | ||
| 25B-1 | Valve bonnet | 1.740 | 50-65 | 1 | 1 | 1 | 3 | 2433-028 | |
| 25B-4 | Valve bonnet | 4.500 | 100 | 1 | 1 | 1 | 1 | 2433-030 | |
| 25C-1 | Front part for cone | 0.095 | 50-65 | 1 | 1 | 1 | 3 | 2444-090 | |
| 25C-3 | Front part for cone | 0.520 | 100 | 1 | 1 | 1 | 1 | 2444-094 | |
| 25D-1 | Rear part for cone | 0.185 | 50-65 | 1 | 1 | 1 | 3 | 2444-091 | |
| 25D-4 | Rear part for cone | 1.000 | 100 | 1 | 1 | 1 | 1 | 2444-095 | |
| 25E-1 | Screw for valve cone | 0.020 | 50-65 | 1 | 1 | 1 | 3 | 2444-017 | |
| 25E-4 | Screw for valve cone | 0.120 | 100 | 1 | 1 | 1 | 1 | 2444-018 | |
| 25F-1 | Gasket for screw dia.31/24 x1,5 | 0.0001 | 50-65 | 1 | 1 | 1 | 3 | 2356-138 | |
| 25F-4 | Gasket for screw dia, 36/28 x 1,5 | 0.001 | 100 | 1 | 1 | 1 | 1 | 2356-141 | |
| 25G-1 | Threaded connection | 0.180 | 50-65 | 1 | 1 | 1 | 3 | 2445-053 | |
| 25G-4 | Threaded connection | 0.400 | 100 | 1 | 1 | 1 | 1 | 2445-061 | |
| 25H-1 | Sealing ring dia. 62/45 x 3 | 0.004 | 50-65 | 1 | 1 | 1 | 3 | 2354-003 | |
| 25H-4 | Sealing ring dia. 110/90 x 3 | 0.020 | 100 | 1 | 1 | 1 | 1 | 2354-117 | |
| 25J-1 | Gasket for bonnet dia. 72,39 x 5.33 | 0.010 | 50-65 | 1 | 1 | 1 | 3 | 1331-154 | |
| 25J-4 | Gasket for bonnet dia. 116,84 x 7 | 0.015 | 100 | 1 | 1 | 1 | 1 | 1331-198 | |
| 25K-1 | Spindle | 0.250 | 50-65 | 1 | 1 | 1 | 3 | 2442-023 | |
| 25K-4 | Spindle | 0.480 | 100 | 1 | 1 | 1 | 1 | 2442-028 | |
| 25L-1 | Lock washer for spindle | 0.010 | 50-65 | 1 | 1 | 1 | 3 | 2445-019 | |
| 25L-4 | Lock washer for spindle | 0.015 | 100 | 1 | 1 | 1 | 1 | 2445-020 | |
| 25M-1 | Packing giand Compl. with o-rings pos. 25R-1 | 0.120 | 50-65 | 1 | 1 | 1 | 3 | 2452-132 | |
| 25M-4 | Packing gland Compl. with o-rings pos- 25R-4 | 0.250 | 100 | 1 | 1 | 1 | 1 | 2452-133 | |
| 25N-1 | Guide pin | 0.002 | 50-65 | 1 | 1 | 1 | 3 | 1445-085 | |
| 25N-4 | Guide pin | 0.002 | 100 | 1 | 1 | 1 | 1 | 1445-085 | |
| 25P-1 | 0-ring dia. 21,8 x 3,5*) | 0.002 | 50-65 | 1 | 1 | 1 | 1 | 1331-020 | |
| 25P-4 | 0-ring dia. 28,2 x 3,5*) | 0.002 | 100 | 1331-024 | |||||
| 25Q-1 | Nylon washer dia. 28.5/28 x 1,5 | 0.001 | 50-65 | 1 | 1 | 1 | 3 | 2354-018 | |
| 25Q-4 | Nylon washer dia. 48/34 y. 1,5 | 0.002 | 100 | 1 | 1 | 1 | 1 | 2354-017 | |
| 25R-1 | O-ring dia.17,12 x 3,5*) | 0,001 | 50-65 | 2 | 2 | 2 | 2 | 1331-016 | |
| 25R-4 | O-ring dia.21.8 x 3,5 | 0.002 | 100 | 2 | 2 | 2 | 2 | 1331-020 | |
| 25S-1 | Hand wheel dia. 120 | 0.160 | 50-65 | 1 | 1 | 1 | 3 | 1365-036 | |
| 25S-4 | Hand wheel dia. 180 | 0.800 | 100 | 1 | 1 | 1 | 1 | 1365-035 | |
| 25T-1 | Screw for hand wheel M5 x 10 | 0.002 | 50-65 | 1 | 1 | 1 | 3 | 1424-140 | |
| 25T-4 | Screw for hand wheei M8 x 16 | 0.010 | 100 | 1 | 1 | 1 | 1 | 1424-166 | |
| 25U-1 | Washer for hand wheel | 0.001 | 50-65 | 1 | 1 | 1 | 3 | 1436-024 | |
| 25U-4 | Washer for hand wheel | 0.003 | 100 | 1 | 1 | 1 | 1 | 1436-026 | |
| 25Y-3 | Gasket for welding nipple | 0.015 | 50-65 | 1 | 1 | 1 | 1 | 2356-087 | |
| 25Y-4 | Gasket for welding nipple | 0.025 | 100 | 1 | 1 | 1 | 1 | 2356-104 | |
| 25Z-1 | Screw valve/compr. M14 x 40 | 0.050 | 50 | 4 | 4 | 4 | 4 | 1424-241 | |
| 25Z-3 | Screw vaive/cornpr. M14 x 45 | 0.050 | 65 | 4 | 4 | 4 | 4 | 1424-242 | |
| 25Z-4 | Screw vaive/cornpr. M16 x 45 | 0.095 | 100 | 4 | 4 | 4 | 4 | 1424-102 | |
| 25AC-3 | Counter flange | 65 | 1 | 1 | 1 | 1 | 2344-019 | ||
| 25AC-4 | Counter flange | 100 | 1 | 1 | 1 | 1 | 2344-020 | ||
| 25AD-3 | Welding nippie dia. 65 | 65 | 1 | 1 | 1 | 1 | 2322-103 | ||
| 25AD-4 | Welding nipple dia. 100 | 100 | 1 | 1 | 1 | 1 | 2322-108 | ||
| 25AF-3 | Threaded plug 3/4" BSP | 65 | 1 | 1 | 1 | 1 | 2314-065 | ||
| 25AF-4 | Threaded plug 3/4" BSP | 100 | 1 | 1 | 1 | 1 | 2314-065 | ||
| 25AG-1 | Gasket for valve/cornpr. | 0.016 | 50 | 2354-105 | |||||
| 25AG-3 | Gasket for valve/compr. | 0.016 | 65 | 1 | 1 | 1 | 1 | 2354-105 | |
| 25AG-4 | Gasket for valvs/compr | 0.020 | 100 | 2354-106 | |||||
| 25AH-3 | Gasket for plug | 0.002 | 65 | 1 | 1 | 1 | 1 | 2356-139 | |
| 25AH-4 | Gasket for piug | 0,002 | 100 | 1 | 1 | 1 | 1 | 2356-139 | |
| 25AJ-1 | Screw bonnet/valve M10 x 25 | 50 | 8 | 1424-191 | |||||
| 25AJ-2 | Screw bonnet/valve M10 x 25 | 50 | 8 | 1424-191 | |||||
| 25AJ-3 | Screw bonnet/valve M10 x 25 | 65 | 8 | 8 | 8 | 8 | 1424-191 | ||
| 25AJ-4 | Screw bonnet/valve M12 x 30 | 0.040 | 100 | 8 | 8 | 8 | 8 | 1424-215 | |
| 25AK-3 | Screw for counter flange M10 x 40 | 0.030 | 65 | 6 | 6 | 6 | 6 | 1424-194 | |
| 25AK-4 | Screw for counter flange M12 x 50 | 50 | 100 | 6 | 6 | 6 | 6 | 1424-219 | |
| Pos. | Designation | Weight each in kg | Number each compresssor | Part No | |||
| SMC 104 | SMC 106 | SMC 108 | TSMC 108 | ||||
| Pressure gauges | |||||||
| Suction and pressure gauge | |||||||
| 30A-1 | R717 | 1.640 | 1 | 1 | 1 | 1 | 1541-108 |
| 30A-2 | Rl2,R22 and R502 | 1.620 | 1 | 1 | 1 | 1 | 1541-232 |
| 30A-3 | R22.R134a and R404A | 1.620 | 1 | 1 | 1 | 1 | 1541-074 |
| 30B-1 | Nozzle and gasket dia.14/0,8 x 1,5 | 0.001 | 1 | 1 | 1 | 1 | 3146-013 |
| 30C-1 | Gasket dia. 11/4x 1,5 | 0.001 | 1 | 1 | 1 | 1 | 2356-119 |
| SMC: discharge pressure gauge | |||||||
| 31A-1 | R717 | 1.380 | 1 | 1 | 1 | 1541-029 | |
| 31A-2 | R12,R22 and R502 | 1.400 | 1 | 1 | 1 | 1541-160 | |
| 31A-3 | R22,R134a and R404A | 1.400 | 1 | 1 | 1 | 1541-075 | |
| 31B-1 | Nozzle and gasket dia. 14/0,8 x 1,5 | 0.001 | 1 | 1 | 1 | 3146-013 | |
| TSMC: discharge pressure gauge | |||||||
| 31A-3 | R717 | 1.600 | 1 | 1541-101 | |||
| 31A-4 | R12, R22 and R502 | 1.660 | 1 | 1541-161 | |||
| 31A-5 | R22,Rl34aandR404A | 1.660 | 1 | 1541-076 | |||
| 31B-1 | Nozzle and gasket dia. 14/0,8 x 1,5 | 0.001 | 2 | 3146-013 | |||
| 31C-1 | Screws for gauges M4 x 20 | 6 | 6 | 6 | 6 | 1412-350 | |
| Oil filter | |||||||
| 33-1 | Oil filter complete | 1 | 1 | 1 | 1 | 4524-039 | |
| 33A-1 | Filter element | 1 | 1 | 1 | 1 | 1517-129 | |
| 33B-1 | Gasket | 2 | 2 | 2 | 2 | 2356-202 | |
| 33C-1 | End cover | 1 | 1 | 1 | 1 | 3422-150 | |
| 33D-1 | Rod for filler | 1 | 1 | 1 | 1 | 2112-145 | |
| 33E-1 | Shield for oil filter | 1 | 1 | 1 | 1 | 2158-209 | |
| 33F-1 | Bracket with connection | 1 | 1 | 1 | 1 | 3422-152 | |
| 33G-1 | Distance piece | 1 | 1 | 1 | 1 | 2212-136 | |
| 33H-1 | Rubber gasket | 1 | 1 | 1 | 1 | 1334-012 | |
| 33J-1 | Magnet | 3 | 3 | 3 | 3 | 1517-022 | |
| 33K-1 | iron ring | 3 | 3 | 3 | 3 | 2114-038 | |
| 33L-1 | Washer dia, 17/8.4 | 1 | 1 | 1 | 1 | 1436-034 | |
| 33M-1 | Nut M 8 | 1 | 1 | 1 | 1 | 1433-073 | |
| 33N-1 | Washer dia-24/13 | 1 | 1 | 1 | 1 | 1436-036 | |
| 33O-1 | Nut M12 | 1 | 1 | 1 | 1 | 1433-075 | |
| 33P-1 | O-ring *) | 1 | 1 | 1 | 1 | 1331-009 | |
| 33Q-1 | O-ring *) | 1 | 1 | 1 | 1 | 1331-008 | |
| 33R-1 | Cutting ring joint | 1 | 1 | 1 | 1 | 1349-131 | |
| Suction filter | |||||||
| 34A-1 | Suction filter open, complete | 0.365 | 2 | 2 | 2 | 1 | 3425-082 |
| 34A-2 | Suction filter closed, complete | 0.365 | 1 | 3425-084 | |||
| 34B-1 | Filter bag | 0.035 | 2 | 2 | 2 | 2 | 3425-083 |
| 34C-1 | Inset for lifter bag | 0.025 | 2 | 2 | 2 | 2 | 3424-058 |
| 34D-1 | 0-ring PRP 337 - 75,56 x 5,33 *) | 0.008 | 2 | 2 | 2 | 3 | 1331-042 |
| 34E-1 | Cover for suction filter | 2.400 | 2 | 2 | 2 | 1 | 3422-103 |
| 34F-1 | 0-ring PRP 239 - 91,67 x 3,53 *) | 0.003 | 2 | 2 | 2 | 1 | 1331-080 |
| 34G-1 | Hexagon head screw M 12 x 40 | 0.050 | 8 | 6 | 8 | 4 | 1424-217 |
| 34H-1 | Spring washer dia. 12 | 0.005 | 8 | 8 | 8 | 4 | 1437-026 |
| Discharge pipe for oil filter | |||||||
| 38A-1 | Discharge pipe for oil pump | 0.500 | 1 | 1 | 1 | 1 | 3141-110 |
| 38B-1 | Inside pipe connection to control | 0.090 | 1 | 1 | 1 | 1 | 3141-162 |
| system (compr. without oil cooler) | |||||||
| 38B-2 | Inside pipe connection to control | 0.090 | 1 | 1 | 1 | 1 | 3141-163 |
| system (compr. with OSSI oil cooler | |||||||
| R717) | |||||||
| 38B-3 | Inside pipe connection to contro! | 0.090 | 1 | 1 | 1 | 1 | 3141-164 |
| system (compr. with HE8 oH cooler | |||||||
| HCFC) | |||||||
| 38C-1 | Connection for disharge pipe - | 0.120 | 1 | 2333-025 | |||
| SMC 104 | |||||||
| 38C-2 | Connection for disharge pipe - | 0.190 | 1 | 2333-025 | |||
| SMC 106 | |||||||
| 38C-3 | Connection for disharge pipe - | 0.180 | 1 | 1 | 2333-026 | ||
| SMC 108 and TSMC 108 | |||||||
| 38D-1 | O-ring PRP 212 - 21,80 x 3.53*) | 0.002 | 2 | 2 | 2 | 2 | 1331-020 |
| 38E-1 | O-ring PRP 321 - 29.51 x 5,33*) | 0.004 | 1 | 1 | 1 | 1 | 1331-039 |
| 38F-1 | Gasket dia- 27/21 x 1,5 | 0.001 | 1 | 1 | 1 | 1 | 2356-133 |
| 38G-1 | O-ring dia. 26.58 x 3,5*) | 0.002 | 1 | 1 | 1 | 1 | 1331-023 |
| Analogous control and safety | |||||||
| equipment | |||||||
| 39A-1 | Gauge panel | 0.070 | 1 | 1 | 1 | 1 | 3146-042 |
| 39B-1 | Socket cap screw M10 x 60 | 0.045 | 2 | 2 | 2 | 2 | 1413-382 |
| 39C-1 | Console | 1 | 1 | 1 | 1 | 2213-142 | |
| 39D-1 | Bar for controls (4 controls) | 1 | 1 | 1 | 2213-143 | ||
| 39D-2 | Bar for controls (5 controls) | 1 | 1 | 1 | 1 | 2213-144 | |
| 390-3 | Bar for controls (6 controls) | 1 | 1 | 1 | 1 | 2213-145 | |
| 39D-4 | Bar for controls (7 controls) | 1 | 1 | 1 | 1 | 2213-154 | |
| 39D-5 | Bar for controls (US, SMC) | 1 | 1 | 1 | 2213-368 | ||
| 39D-6 | Bar for controls (US, TSMC) | 1 | 2213-369 | ||||
| 39E-1 | Hexagon head screw M6 x 12 | 2 | 2 | 2 | 2 | 1424-150 | |
| 39F-1 | Spring washer dia. 11/6 | 2 | 2 | 2 | 2 | 1437-022 | |
| 39G-1 | Socket cap screw M4 x 6 | 1412-200 | |||||
| 39H-1 | Spring washer dia. 7/4 | 1437-020 | |||||
| 39J-1 | Socket cap screw M5 x 10 | 4 | 4 | 4 | 4 | 1413-330 | |
| 39K-1 | Spring washer dia. 9/5 | 4 | 4 | 4 | 4 | 1437-021 | |
| Cooling water connection See section: Water cooling oi reciprocating compressor | |||||||
| 40A-1 | Set of hoses for cooling water SMC104 | 0.940 | 1 | 3185-154 | |||
| 40A-2 | Set of hoses for cooling water SMC 106 | 1.000 | 1 | 1 | 3185-155 | ||
| 40A-3 | Set of hoses for cooling water SMC l08 and TSMC108 | 1.400 | 1 | 1 | 3185-156 | ||
| 40B-1 | Hose connection - 3/8" - straight | 0.004 | 12 | 14 | 16 | 16 | 2334-025 |
| 40C-1 | Anote - 3/8" | 0.009 | 8 | 10 | 10 | 10 | 1341-090 |
| 40D-1 | T-piece | 0.015 | 2 | 2 | 2 | 2 | 1341-141 |
| 40E-1 | Hose clamp | 0.015 | 12 | 14 | 16 | 16 | 1345-168 |
| 40F-1 | Cable binder | 3 | 3 | 3 | 3 | 1554-062 | |
| Purge valve | |||||||
| 42A-1 | Purge valve | 0.300 | 1 | 1 | 1 | 2 | 2412-585 |
| 42B-1 | Threaded nipple | 1 | 1 | 1 | 1 | 1349-078 | |
| 42C-1 | Cutting ring | 0.135 | 1 | 1 | 1 | 2 | 1349-062 |
| 42D-1 | Nut | ||||||
| 42E-1 | Nut | 0.070 | 1 | 1 | 1 | 2 | 2313-045 |
| 42F-1 | Connection pipe with collar | 0.025 | 1 | 1 | 1 | 2 | 2334-027 |
| 42G-1 | Gasket | 0.001 | 2 | 2 | 2 | 4 | 2356-123 |
| 42H-1 | Nut | 0.060 | 1 | 1 | 1 | 2 | 2313-027 |
| Pressure and temperature controls Pressure controls for R717 | |||||||
| 45A-1 | KP5A | 0.300 | 1 | 1 | 1 | 1 | 1373-125 |
| 45B-1 | KP15A | 0.460 | 1 | 1 | 1 | 1 | 1373-142 |
| 45C-1 | MP55A | 0.900 | 1 | 1 | 1 | 1 | 1373-162 |
| 42F-1 | Connection pipe with collar | 0.025 | 1 | 1 | 1 | 1 | 2334-027 |
| 42G-1 | Gasket | 0.001 | 2 | 2 | 2 | 2 | 2356-123 |
| 42H-1 | Nut | 0.060 | 1 | 1 | 1 | 1 | 2313-027 |
| Pressure controls for R22, R134a and R404A | |||||||
| 45D-1 | KP5 | 0,3 | 1 | 1 | 1 | 1 | 1373-123 |
| 45E-1 | KP15 | 0.460 | 1 | 1 | 1 | 1 | 1373-135 |
| 45F-1 | MP55 | 0.800 | 1 | 1 | 1 | 1 | 1373-159 |
| Temperature controls: | |||||||
| 45G-1 | KP98 | 0.720 | 1 | 1 | 1 | 1 | 1373-043 |
| 45H-1 | KP77 | 0.350 | 1 | 1 | 1 | 1 | 1373-044 |
| 45J-1 | Phail pocket for temperature controls | 0.770 | 1 | 1 | 1 | 1 | 1377-171 |
| 45K-1 | Gasket | 1 | 1 | 1 | 1 | 2356-133 | |
| AMR 312 S coupling | |||||||
| 48A-4 | Disc pack | 1.132 | 2 | 2 | 2 | 2 | 1524-157 |
| 48B-4 | Bolt | 0.054 | 16 | 16 | 16 | 16 | 1524-165 |
| 48С4 | Bevel washer | 0.010 | 4 | 4 | 4 | 4 | 1524-187 |
| 48D-4 | Lock nut | 0.018 | 16 | 16 | 16 | 16 | 1524-173 |
| 48E-4 | Washer | 0.008 | 16 | 16 | 16 | 16 | 1524-181 |
| Capacity regulation | |||||||
| 50A-1 | Valve body with 1 solenoid valve without coil | 1 | 3143-383 | ||||
| 50A-2 | Valve body with 2 solenoid valves without coils | 1 | 1 | 3143-384 | |||
| 50A-3 | Valve body with 3 solenoid valves without coils | 1 | 3143-385 | ||||
| 50A-4 | Valve body with 4 solenoid valves without coils | 1 | 3143-386 | ||||
| 50B-1 | Coil 220/230V, 50/60 Hz. 10 W | 0.260 | 1372-537 | ||||
| 50B-2 | Coil 110V, 50/60 Hz, 10W | 0.260 | 1372-538 | ||||
| 50B-3 | Cod 240V, 50 Hz, 10 W | 0.062 | 1372-539 | ||||
| 50C | Solenoid vatve (service kit for one solenoid valve) | 1372-424 | |||||
| Crankcase heater | |||||||
| 57A-1 | Crankcase heater - 270 W - 115 V, 1 1/4" BSP | 1 | 1 | 1 | 1 | 3181-034 | |
| 57A-2 | Crankcase heater - 270 W - 230 V, 1 1/4" BSP | 1 | 1 | 1 | 1 | 3181-035 | |
| 57A-3 | Crankcase heater - 270 W - 250 V, 1 1/4" BSP | 1 | 1 | 1 | 1 | 3181-036 | |
| 57B-1 | Gasket dia- 50/43 x 1,5 for 1 1/4" BSP | 0.002 | 1 | 1 | 1 | 1 | 2356-150 |
| 80 | Sofenoide valve blok, complete with 0.6 mm orifice for oil return. Excl. coil | 2.040 | 1 | 1 | 1 | 1 or 2 | 1372-179 |
| Strainer kit consist of: | 1 | 1 | 1 | 1 or 2 | 1372-089 | ||
| 80E | Strainer | ||||||
| 80G | Al-gasket | ||||||
| Service kit consist of: | 1 | 1 | 1 | 1 or 2 | 1372-086 | ||
| 80P | Armature tube | ||||||
| 80H | Armature | ||||||
| 80K | O-ring | ||||||
| 80M | O-ring | ||||||
| 80L | Ai-gasket | ||||||
| 80N | Snap fastener | ||||||
| Seal kit consist of: | 1 | 1 | 1 | 1 or 2 | 1372-091 | ||
| 80G | Al-gasket | ||||||
| 80K | O-ring | ||||||
| 80M | O-ring | ||||||
| 80L | Al-gasket | ||||||
| 80Q | Al-gasket | ||||||
| Orifice kit 0,6 mm consist of: | 1 | 1 | 1 | 1 or 2 | 1371-034 | ||
| 80L | At-gasket | ||||||
| 80Q | At-gasket | ||||||
| 80I | Orifice 0,6 mm | ||||||
| Onftce kit 0,8 mm consist of: | 1 | 1 | 1 | 1 or 2 | 1371-035 | ||
| 80L | Al-gasket | ||||||
| 80Q | Al-gasket | ||||||
| 80I | Orifice 0.8 mm | ||||||
| Orifice kit 1,0 mm consist of: | 1 | 1 | 1 | 1 or 2 | 1371-036 | ||
| 80L | Al-gasket | ||||||
| 80Q | Al-gasket | ||||||
| 80I | Orifice 1,0 mm | ||||||
| Orifice kit 3.3 mm(for thermopump only) consist of: | 1 | 1 | 1 | 1 or 2 | 1371-037 | ||
| 80L | Al-gasket | ||||||
| 80Q | Al-gasket | ||||||
| 80I | Orifice 3.3 mm | ||||||
| 80J-1 | Coil 220/230V, 50/60 H2, 10 W | 0.285 | 1372-537 | ||||
| 80J-2 | Coil 110V, 50/60 Hz, 10W | 0.285 | 1372-538 | ||||
| 80J-3 | Coil 240 V, 50 Hz, 10W | 0.285 | 1372-539 | ||||
| 80J-4 | Coil 24 V. SO Hz, 10 W | 0.285 | 1372-541 | ||||
| Intermediate pressure connections | |||||||
| 90A-1 | Mixing chamber with flange | 9.500 | 1 | 3114-095 | |||
| 90B-1 | Counter flange for mixing chamber | 1.700 | 1 | 3115-084 | |||
| 90C-1 | Intermediate ring | 0.392 | 1 | 3422-100 | |||
| 90D-1 | 0-ring PRP 236 - 82,15 3.53 ') | 0.002 | 1 | 1331-077 | |||
| 90E-1 | 0-ringPRP241 -98.02x3,5') | 0.002 | 1 | 1331-081 | |||
| 90F-1 | Hexagon head screw M12 x 65 | 0.065 | 4 | 1424-222 | |||
| 90G-1 | Hexagon head screw Ml 4 x 55 | 0.065 | 4 | 1424-246 | |||
| 90H-1 | Hexagon head screw Ml 4 x 55 | 0.005 | 4 | 1437-026 | |||
| 90J-1 | Spring washer dia. 12 | 0.004 | 4 | 1437-030 | |||
| 90K-1 | Spring washer dia. 14 | 0.025 | 4 | 1432-066 | |||
| 90L-1 | Nut M14 | 0.003 | 1 | 1331-080 | |||
| 90M-1 | 0-ring PRP 239-91 ,67 x 3,53 *) | 0.065 | 1 | 2313-027 | |||
| 90N-1 | CapGasket dia. 18/10 x 1.5 | 0.002 | 1 | 2356-123 | |||
| Oil cooling - type HE8 S for R22 | |||||||
| 92A-1 | Oil cooler | 1 | 1 | 1 | 1 | 4242-038 | |
| 92B-1 | Stop valve 8MSL 10 | 0.300 | 1 | 1 | 1 | 1 | 1374-171 |
| 92C-1 | Thermostatic expansion valve TX 2 - 0,5 | 0.400 | 1 | 1 | 1 | 1 | 1371-305 |
| 92D-1 | Solenoid valve without coil | 0.346 | 1 | 1 | 1 | 1 | 1372-422 |
| 92N-1 | Coil 220/230V, 50/60 Hz, -10 W | 0.260 | 1372-537 | ||||
| 92N-2 | Coil 110V, 50/60 Hz, 10W | 0.260 | 1372-538 | ||||
| 92N-3 | Coil 240V, 50 Hz, 10W | 0.260 | 1372-539 | ||||
| 92E-1 | Filter | 0.320 | 1 | 1 | 1 | 1 | 4522-002 |
| 90F-1 | Screwed connection GE 10-LR 1/4" | 0.050 | 6 | 6 | 6 | 6 | 1349-051 |
| 92G-1 | Single banjo connector DSVW 10-LR | 0.160 | 1 | 1 | 1 | 1 | 1349-089 |
| 92H-1 | Threaded nipple | 0.110 | 1 | 1 | 1 | 1 | 2314-056 |
| 92J-1 | Threaded plug for 8/6 mm pipe | 0.015 | 2 | 2 | 2 | 2 | 2314-053 |
| 92K-1 | Gasket dia. 19/14 x 1,5 - aluminium | 0.001 | 2 | 2 | 2 | 2 | 2356-124 |
| 92L-1 | Connection piece for 1 pipe dia. 8 mm | 0.030 | 2 | 2 | 2 | 2 | 2333-021 |
| 92M-1 | Gasket- dia. 27/21 x 1,5 - aluminium | 0,001 | 3 | 3 | 3 | 3 | 2356-133 |
| Oil cooling - type OOSl for R717 | |||||||
| 93A-1 | Oil cooler | 1 | 1 | 1 | 1 | 4242-029 | |
| 93B-1 | Stop valve SN 6 | 1 | 1 | 1 | 1 | 2413-010 | |
| 93C-1 | Thermostatic injection TEAT 20-2 | 0.400 | 1 | 1 | 1 | 1 | 1371-240 |
| 93D-1 | Solenoid valve without coil | 0.346 | 1 | 1 | 1 | 1 | 1372-422 |
| 93N-1 | Coil 220/230V. 50/60 Hz, 10 W | 0.260 | 1372-537 | ||||
| 93N-2 | Coil 110V, 50/60 Hz, 10W | 0.260 | 1372-538 | ||||
| 93N-3 | Coil 240V, 50Hz.Tow | 0.260 | 1372-539 | ||||
| 93E-1 | Filter | 0.320 | 1 | 1 | 1 | 1 | 4522-002 |
| 93F-1 | Screwed connection GE 10-LR 1/4" | 0.050 | 6 | 6 | 6 | 6 | 1349-051 |
| 93G-1 | Single banjo connector DSVW 10-LR | 0.160 | 1 | 1 | 1 | 1 | 1349-089 |
| 93H-1 | Threaded nipple | 0.110 | 1 | 1 | 1 | 1 | 2314-056 |
| 93J-1 | Threaded piug for dia. 8/6 mm pipe | 0.015 | 4 | 4 | 4 | 4 | 2314-053 |
| 93K-1 | Gasket dia. 19/14 x 1.5 - alunimium | 0.001 | 8 | 8 | 8 | 8 | 2356-124 |
| 93L-1 | Connection piece for 1 pipe dia. 8 mm | 0.030 | 4 | 4 | 4 | 4 | 2333-021 |
| 93M-1 | Gasket dia. 27/21 x 1,5 - aluminium | 0.001 | 3 | 3 | 3 | 3 | 2356-133 |
| Chain drive for oil pump | |||||||
| 96A-1 | Hub for chain wheel (chranshaft) | 1 | 1 | 1 | 1 | 2126-020 | |
| 96B-1 | Hub for chain wheel (oil pump) | 1 | 1 | 1 | 1 | 2126-019 | |
| 96C-1 | Chain wheel (crankshaft) | 1 | 1 | 1 | 1 | 2126-018 | |
| 96D-1 | Chain wheel (oi! pump) | 1 | 1 | 1 | 1 | 2126-017 | |
| 96E-1 | Chain | 1 | 1 | 1 | 1 | 1521-102 | |
| 96F-1 | Hexagon head screw | 5 | 5 | 5 | 5 | 1424-150 | |
| 96G-1 | Spring washer | 5 | 5 | 5 | 5 | 1437-022 | |
| 96H-1 | Shield for oil | 1 | 1 | 1 | 1 | 3141-128 | |
| 98 | Thermo pump | ||||||
| 98A-1 | Side cover for thermo pump | 1 | 1 | 1 | 1 | 3113-145 | |
| 98B-1 | Monitor box | 1 | 1 | 1 | 1 | 1553-215 | |
| Alien screw M4 x 16 | 2 | 2 | 2 | 2 | 1412-204 | ||
| Spring washer dia. 4 | 2 | 2 | 2 | 2 | 1437-020 | ||
| 98C-1 | Level indicator | 2 | 2 | 2 | 2 | 3185-038 | |
| 98D-1 | Outer part for level indicator | 2 | 2 | 2 | 2 | 3185-034 | |
| 98E-1 | Washer dia. 20/13x1.5 | 2 | 2 | 2 | 2 | 2356-125 | |
| 98F-1 | Rubber cap | 2 | 2 | 2 | 2 | 1554-194 | |
| 98G-1 | Solenoid valve without coil | 1 | 1 | 1 | 1 | 1372-422 | |
| 98H-1 | Solenoid valve without coil | 1 | 1 | 1 | 1 | 1372-423 | |
| 98J-1 | Coil 220/230V, 50/60 Hz, 10 W | 0,285 | 1372-537 | ||||
| 98J-2 | Coil 110V, 50/60 H2. 10W | 0.285 | 1372-538 | ||||
| 98J-3 | Coil 240V. 50 Hz, 10W | 0,285 | 1372-539 | ||||
| 98K-1 | Check valve | 2 | 2 | 2 | 2 | 1364-008 | |
| Straight joint 10 mm BSP | 6 | 6 | 8 | 5 | 1349-051 | ||
| Socket 10 mm BSP | 5 | 5 | 4 | 4 | 1349-101 | ||
| T-joint 10 mm | 3 | 4 | 5 | 1 | 1349-041 | ||
| Strap for stop valve | 1 | 1 | 1 | 1 | 2212-059 | ||
| Cable binder no. 10 | 1 | 1 | 1 | 1 | 1554-054 | ||
| Allen screw M4 x 12 | 2 | 2 | 2 | 2 | 1412-203 | ||
| Nut M4 | 2 | 2 | 2 | 2 | 1432-035 | ||
| 98L-1 | Washer dia. 29/21 x 1,5 | 2 | 2 | 2 | 2 | 2356-136 | |
| 98M-1 | VA-joint with nozzle 1,2 mm | 3 | 4 | 5 | 2314-097 | ||
| 98M-2 | VA-joint with nozzle 0,6 mm | 1 | 2314-100 | ||||
| Angle joint | 3 | 3 | 2 | 1 | 1349-033 | ||
| Angle swivel joint 8 mm | 4 | 4 | 4 | 1349-087 | |||
| Angle swivel joint 10 mm | 3 | 3 | 2 | 1 | 1349-089 | ||
| Angle joint 10 mm | 1 | 1349-112 | |||||
| Bushing 1/4" x 1/2" RG | 2 | 1 | 1 | 2312-013 | |||
| Threaded nipple | 1 | 1 | 2314-056 | ||||
| Gasket dia. 27/21 x 1,5 Al | 2 | 2 | 2 | 2356-133 | |||
| Gasket dia. l9/14 x 4 Al | 3 | 3 | 3 | 1 | 2356-283 | ||
| Pipe strap dia. 10x15 | 2 | 1 | 1377-117 | ||||
| Hexagon set screw M6 x 12 | 1 | 1 | 1424-150 | ||||
| Nut M6 | 1 | 1432-061 | |||||
| Allen screw M5 x 10 | 1 | 1413-330 | |||||
| Washer dia. 12,5/6,4 x 1,6 | 2 | 1436-033 | |||||
| Spring washer for M6 | 1 | 1437-021 | |||||
| 98N-1 | Filter | 1 | 1 | 1 | 1 | 4522-002 | |
| 98P-1 | Stop valve. | 1 | 1 | 1 | 1 | 2412-277 | |
| 98Q-1 | Cooling cover | 1 | 1 | 1 | 1 | 3113-143 | |
| 98R-1 | Gasket for side cover | 1 | 1 | 1 | 1 | 2353-189 | |
| 98S-1 | Hexagon head screw M14 x 80 | 16 | 16 | 16 | 16 | 1424-081 | |
| 98T-1 | Oil cooler OSSI | 1 | 1 | 1 | 1 | 4242-029 | |
| Socket 1/4" | 1 | 1 | 1 | 1 | 1349-101 | ||
| 98U | Solenoid valve without coil | 1 | 1 | 1 | 1372-422 | ||
| 98V | Solenoid valve without coii | 1 | 1 | 1 | 1 | 1372-422 | |
| 98AB-1 | Coil 220/230V, 50/60 Hz, 10 W | 0.285 | 1372-537 | ||||
| 98AB-2 | Coii 110V, 50/60 Hz. 10W | 0.285 | 1372-538 | ||||
| 98AB-3 | Coil 240V, 50 Hz, 10 W | 0.285 | 1372-539 | ||||
| 98X | PT100 sensor | 1 | 1 | 1 | 1 | 1373-253 | |
| 98Y | Stop valve | 1 | 1 | 1 | 1 | 2412-277 | |
| 98Z | Non-return valve | 1 | 1 | 1 | 1 | 1364-022 | |
| 98AA | Screw joint | 1 | 1 | 1 | 1 | 2314-105 | |
| UNISAB | |||||||
| 99A-1 | Support for UNISAB | 1 | 1 | 1 | 1 | 2213-500 | |
| 99B-3 | Distance washers | 4 | 4 | 4 | 4 | 2212-130 | |
| 99C-1 | Screw for support M10 x 20 | 2 | 2 | 2 | 2 | 1424-190 | |
| 99D-1 | Screw for UNlSAB M6 x 20 | 4 | 4 | 4 | 4 | 1424-152 | |
| 99E-1 | Washers dia, 22/7 x 1,5 | 4 | 4 | 4 | 4 | 1436-025 | |
| Toots set for compressor |
| SMC 104-116 Mk3 & TSMC 108-116 Mk3. type S-L-E |
| Line no. A600 = Normal set, tools set no 3183-109 |
| Line no. A601 = Extended set, tools set no 3183-110 |
| Line no. A602A = Tools for coupling (SMC 104-108) |
| Line no. A602B =Toots for coupling (SMC 112-116) |
| Line no. A603 = Toots for alignment of coupling |
| Pos.No | Designation | Dimension | Line No | Part No | ||||
| A600 | A601 | A602 | A603 | |||||
| A | B | |||||||
| 1-1 | Clamp with screw, compr. type S and L | 4 | 4 | 3183-144 | ||||
| 1-2 | Clamp with screw, compr. type E | 4 | 4 | 3183-145 | ||||
| 2 | Tools for shaft seal | 1 | 1 | 3183-139 | ||||
| 3 | Tommy screw for cylinder liner | 2 | 2 | 3183-041 | ||||
| 4 | Theaded plug for unloading cylinder | 3/8"BSP | 2 | 2 | 2314-017 | |||
| 5 | Supporting plate for pistons | 8 | 8 | 3183-115 | ||||
| 6 | Spanner for heating cartridge | NV 55 | 1 | 1 | 3183-060 | |||
| 7 | Trigger for coupling or belt pulley | 1 | 1 | 3183-059 | ||||
| 8 | Adjusting jig for coupling | 1 | 3183-105 | |||||
| 9-1 | Wrench for cylinder screw | NV 4 | 1 | |||||
| 9-2 | Wrench for cylinder screw | NV 5 | 1 | |||||
| 9-3 | Wrench for cylinder screw | NV 8 | 1 | |||||
| 9-4 | Wrench for cylinder screw | NV 10 | 1 | |||||
| 9-5 | Special wrench for shaft seal | NV 4 | 1 | 1612-392 | ||||
| 10-1 | Retaining-ring plier | J21/G | 1 | |||||
| 10-2 | Retaining-ring plier | A11/G | 1 | |||||
| 11-1 | Open end and ring spanner | NV 10 | 1 | |||||
| 11-2 | Open end and ring spanner | NV 17 | 1 | |||||
| 11-3 | Open end and ring spanner | NV 19 | 1 | |||||
| 11-4 | Open end and ring spanner | NV 22 | 1 | |||||
| 11-5 | Open end and ring spanner | NV 24 | 1 | |||||
| 11-6 | Open end and ring spanner | NV 27 | 1 | |||||
| 13-1 | Socket wrench | NV10 | 1 | |||||
| 13-2 | Socket wrench | NV13 | 1 | |||||
| 13-3 | Socket wrench | NV17 | 1 | |||||
| 13-4 | Socket wrench | NV19 | 1 | |||||
| 13-5 | Socket wrench | NV22 | 1 | |||||
| 13-6 | Socket wrench | NV24 | 1 | 1 | 1 | |||
| 13-7 | Socket wrench | NV27 | 1 | |||||
| 13-8 | Socket wrench | NV30 | 1 | |||||
| 13-9 | Socket wrench | NV32 | 1 | |||||
| 13-10 | Socket wrench | NV9/16" | 1 | |||||
| 13-11 | Socket wrench | NV 3/4" | 1 | 1 | ||||
| 13-12 | Socket wrench | NV11/16" | 1 | 1 | ||||
| 14 | Ratchet handle | 1 | ||||||
| 15 | Speed handle | 1 | ||||||
| 16 | Universal joint for socket wrench | 1 | ||||||
| 17-1 | Extension rod for socket wrench | 1 | ||||||
| 17-2 | Extension rod for socket wrench | 1 | ||||||
| 19-1 | Torque wrench 15-90 Nm | 1 | ||||||
| 19-2 | Torque wrench 40-200 Nm | 1 | 1 | 1 | ||||
| 20 | Coupler for torque wrench 1/2 | 2 | 1 | 1 | ||||
| 21-1 | Open spanner for torque wrench | NV 11/16" | 1 | 1 | ||||
| 21-2 | Open spanner for torque wrench | NV 3/4" | 1 | 1 | ||||
| 22 | Feeler gauge | 1 | 1 | |||||
